Umair Ramzan 
If you’re caught in the rain with your skateboard, or if your board gets wet for any other reason, it’s important to take care of it immediately. Water can damage your skateboard in a number of ways, so it’s best to avoid getting it wet if at all possible. But if it does get wet, here’s what you need to do.
First, remove any moisture from the surface of the board as soon as possible. Use a towel or rag to wipe away any water that’s on the top and bottom of the deck. Then, turn the board over and do the same on the underside.
Next, let the board air dry in a warm place. Do not put it in direct sunlight, as this can cause the wood to warp. Once it’s completely dry, you can ride it as usual.
If your board gets soaked, however, you’ll need to take some extra steps. First, remove all of the hardware from the deck – that includes the trucks, wheels, and bearings. Then, place the board in a warm place and allow it to air dry completely.
Once it’s dry, you’ll need to inspect the deck for any water damage. If there are any soft spots or warping, the deck will need to be replaced. The same goes for any damaged hardware.
So, that’s what you need to do if your skateboard gets wet. Be sure to take care of it right away to avoid any further damage. And, if the worst does happen, don’t despair – you can always get a new one and start skating again.
What to do to prevent your skateboard from getting wet?
Just because your skateboard has gotten wet doesn’t mean it’s ruined, and there are some tricks you can use to make sure your skateboard stays in shape. To prevent your skateboard from getting wet, you can purchase a skid plate or use a tape or wax to help protect your skateboard. If your skateboard is wet, you’ll need to let it dry.
If you have a dry skateboard, you’ll need to dry it off with a towel. You can also take your skateboard to a professional skate store and they will clean it for you. If your skateboard is really wet and you don’t have access to a professional, you can place it in a bowl or pan and cover it with a light layer of cornstarch to prevent it from warping.
How do you clean your skateboard after it gets wet?
If your skateboard gets wet, it is important to clean it immediately. You should not just wipe it down with a wet cloth because you risk damaging the board itself. You should use a cleaning agent that is safe for the board. You should also place it in a bag or wrap it in a towel. It is important to clean the deck of your skateboard because the deck is the part of the skateboard that is in contact with the ground.
Skateboard Safety Tips in the rain
If your skateboard gets wet, you should take the following safety precautions:The average cost of a skateboard is $100, and kids can easily lose this investment in a matter of seconds. It’s easy to ruin a skateboard because of the way they are made. When it rains, check that your skateboard is well protected. The best way to protect your board is by using a waterproof cover. Another option is to use a skateboard bag. To keep the board safe during the rain, just make sure that you have a dry cloth or towel on hand.
FAQs
Does rain ruin a skateboard?
Yes,rain ruin a skateboard.
How do I know if my skateboard is waterlogged?
To try and check if your skateboard is waterlogged, you should try to push down on the deck and see if it gives. If it does, then you might want to reconsider buying it.
Can you wash a skateboard?
Yes, you can wash your skateboard wire brush or toothbrush and use some dishwashing soap to clean them properly.
How do you get water out of skateboard bearings?
If the bearings are wet then you can use a paper towel to get the water out. If the bearings are dry then you can use a rag to dry them out. The best way to dry them out is to put them in the sun at a distance from the ground so that the heat from the sun helps dry them out.
Can I clean my griptape with water?
Absolutely. Griptape is water-resistant like most outdoor surfaces, so it should be fine.
How do I make my griptape more grippy?
You can apply a thin layer of graphite to your griptape to make it more grippy. The graphite will be absorbed into the wood and will create a smoother surface that lessens the friction so the wheel will actually glide across the surface instead of catching on the wood.
